The machine is specified for air purifier filter production, where the pleated media has to be bonded and cut into fixed panel lengths without stringing or glue drip at the cut edge. Hot melt adhesive output is controlled by servo, so glue dosage is adjusted through the control system rather than by manual valve setting.
The line applies intermittent adhesive strips to pleated PP filter media, then cuts the pleats at the glue line to produce bonded filter panels. It is built for air purifier filter production across different specifications.
The machine measures 5700 × 1190 × 1830mm. Total power is 17.5kW, of which 7.5kW is the hot melt glue machine. Working air pressure is 0.6MPa, and the power supply is 380V / 50Hz.
The line dispenses 2 × 26 adhesive strips at a bead distance of 25.4mm. Glue cut is pleat-based, with peak and valley dispensing and cross glue cut supported on both front and reverse sides. The glue gun is a zero-drip high-speed type with no stringing, mounted on an upper and lower supporting structure.
Hot melt adhesive output is fast, and glue dosage is adjusted through servo control. The servo control allows the adhesive volume to be set per production run rather than fixed by a mechanical valve.
The machine body of this Fully-automatic PP Intermittent Gluing Production Line is made of stainless steel. The glue gun adopts an upper and lower supporting structure, which holds the gun position stable across the 700mm feeding width.
| Specification | Value |
| Max Feeding Width | 700mm |
| Pleating Height | 8–80mm |
| Production Speed | 4–27m/min |
| Beads Distance | 25.4mm |
| Number of Adhesive Strips | 2 × 26 strips |
| Voltage / Power Supply | 380V / 50Hz |
| Total Power | 17.5kW (including hot melt glue machine 7.5kW) |
| Working Air Pressure | 0.6MPa |
| Machine Dimensions (L × W × H) | 5700 × 1190 × 1830mm |
Glue dosage is adjusted through servo control rather than a fixed mechanical valve. Hot melt adhesive output is fast, and the adhesive volume can be set per production run to match the filter specification.
The glue gun is a zero-drip high-speed type with no stringing. This matters at the cut edge, where a stringing gun leaves adhesive threads that contaminate the cut and require downstream cleaning.
The glue gun adopts an upper and lower supporting structure, which holds the gun position stable across the full 700mm feeding width. A cantilevered gun would deflect at the far edge, producing uneven adhesive volume between the near and far strips.
The line supports pleat-based glue cut, peak and valley dispensing, and cross glue cut on front and reverse sides. These three modes cover the bonding patterns used in air purifier filter construction without changing the machine configuration.
The line dispenses 2 × 26 adhesive strips at a 25.4mm bead distance. The strip count and bead distance are fixed machine parameters, which suits air purifier filters built to the standard 25.4mm pleat pitch.
The machine body is made of stainless steel, which resists adhesive buildup and is compatible with the cleaning routines used in filter production.
The Fully-automatic PP Intermittent Gluing Production Line is specified for air purifiers of various specifications. The 700mm feeding width and 8–80mm pleating height cover the filter panel formats used in residential and commercial air purifier units.
The line applies intermittent adhesive strips to pleated PP filter media and cuts the pleats at the glue line to produce bonded filter panels. It is specified for air purifier filter production across different specifications.
Maximum feeding width is 700mm. Pleating height range is 8–80mm. Production speed is 4–27m/min.
The line dispenses 2 × 26 adhesive strips at a bead distance of 25.4mm. The bead distance is a fixed machine parameter matched to the standard pleat pitch used in air purifier filters.
Glue dosage is adjusted through servo control rather than a fixed mechanical valve. Hot melt adhesive output is fast, and the adhesive volume can be set per production run.
The glue gun is a zero-drip high-speed type with no stringing. The gun adopts an upper and lower supporting structure, which holds the gun position stable across the 700mm feeding width.
The Fully-automatic PP Intermittent Gluing Production Line supports pleat-based glue cut, peak and valley dispensing, and cross glue cut on front and reverse sides. These cover the bonding patterns used in air purifier filter construction.
The line requires 380V / 50Hz power. Total power is 17.5kW, including the hot melt glue machine at 7.5kW. Working air pressure is 0.6MPa.
The machine measures 5700 × 1190 × 1830mm (L × W × H). The machine body is made of stainless steel.
Feeding width, pleating height and gluing mode are confirmed against the filter specification before the order. Send the filter panel dimensions, pleat height and required bonding pattern, and we will confirm the line configuration.
Send the filter panel dimensions, pleat height within the 8–80mm range, feeding width within 700mm, and the required gluing mode. We will confirm the configuration and quotation based on those requirements.
Address
Hongchuangyuan, Dongshan Street, Rui'an City, Wenzhou, Zhejiang Province, China
Tel
